extract and manual bug fix

data/registers/vrefbuf_v1.yaml

@@ -0,0 +1,77 @@
+block/VREFBUF:
+  description: Voltage reference buffer.
+  items:
+  - name: CSR
+    description: control and status register.
+    byte_offset: 0
+    fieldset: CSR
+  - name: CCR
+    description: calibration control register.
+    byte_offset: 4
+    fieldset: CCR
+fieldset/CCR:
+  description: calibration control register.
+  fields:
+  - name: TRIM
+    description: Trimming code.
+    bit_offset: 0
+    bit_size: 6
+fieldset/CSR:
+  description: control and status register.
+  fields:
+  - name: ENVR
+    description: Voltage reference buffer mode enable.
+    bit_offset: 0
+    bit_size: 1
+    enum: ENVR
+  - name: HIZ
+    description: High impedance mode.
+    bit_offset: 1
+    bit_size: 1
+    enum: HIZ
+  - name: VRS
+    description: Voltage reference scale.
+    bit_offset: 2
+    bit_size: 1
+    enum: VRS
+  - name: VRR
+    description: Voltage reference buffer ready.
+    bit_offset: 3
+    bit_size: 1
+    enum: VRR
+enum/ENVR:
+  bit_size: 1
+  variants:
+  - name: Disabled
+    description: Internal voltage reference mode disable (external voltage reference mode).
+    value: 0
+  - name: Enabled
+    description: Internal voltage reference mode (reference buffer enable or hold mode) enable.
+    value: 1
+enum/HIZ:
+  bit_size: 1
+  variants:
+  - name: Connected
+    description: VREF+ pin is internally connected to the voltage reference buffer output.
+    value: 0
+  - name: HighZ
+    description: VREF+ pin is high impedance.
+    value: 1
+enum/VRR:
+  bit_size: 1
+  variants:
+  - name: NotReady
+    description: The voltage reference buffer output is not ready.
+    value: 0
+  - name: Ready
+    description: The voltage reference buffer output reached the requested level.
+    value: 1
+enum/VRS:
+  bit_size: 1
+  variants:
+  - name: V2_048
+    description: Voltage reference set to VREF_OUT1 (around 2.048 V).
+    value: 0
+  - name: V2_5
+    description: Voltage reference set to VREF_OUT2 (around 2.5 V).
+    value: 1

data/registers/vrefbuf_v2a.yaml

@@ -0,0 +1,37 @@
+block/VREFBUF:
+  description: Voltage reference buffer.
+  items:
+  - name: CSR
+    description: VREFBUF control and status register.
+    byte_offset: 0
+    fieldset: CSR
+  - name: CCR
+    description: VREFBUF calibration control register.
+    byte_offset: 4
+    fieldset: CCR
+fieldset/CCR:
+  description: VREFBUF calibration control register.
+  fields:
+  - name: TRIM
+    description: 'Trimming code The TRIM code is a 6-bit unsigned data (minimum 000000, maximum 111111) that is set and updated according the mechanism described below. Reset: TRIM[5:0] is automatically initialized with the VRS = 0 trimming value stored in the Flash memory during the production test. VRS change: TRIM[5:0] is automatically initialized with the trimming value (corresponding to VRS setting) stored in the Flash memory during the production test. Write in TRIM[5:0]: User can modify the TRIM[5:0] with an arbitrary value. This is permanently disabling the control of the trimming value with VRS (until the device is reset). Note: If the user application performs the trimming, the trimming code must start from 000000 to 111111 in ascending order.'
+    bit_offset: 0
+    bit_size: 6
+fieldset/CSR:
+  description: VREFBUF control and status register.
+  fields:
+  - name: ENVR
+    description: Voltage reference buffer mode enable This bit is used to enable the voltage reference buffer mode.
+    bit_offset: 0
+    bit_size: 1
+  - name: HIZ
+    description: High impedance mode This bit controls the analog switch to connect or not the VREF+ pin. Refer to for the mode descriptions depending on ENVR bit configuration.
+    bit_offset: 1
+    bit_size: 1
+  - name: VRR
+    description: Voltage reference buffer ready.
+    bit_offset: 3
+    bit_size: 1
+  - name: VRS
+    description: 'Voltage reference scale These bits select the value generated by the voltage reference buffer. VRS = 000: VREFBUF0 voltage selected. VRS = 001: VREFBUF1 voltage selected. VRS = 010: VREFBUF2 voltage selected. VRS = 011: VREFBUF3 voltage selected. Others: Reserved Note: Refer to the product datasheet for each VREFBUFx voltage setting value. The software can program this bitfield only when the VREFBUF is disabled (ENVR=0).'
+    bit_offset: 4
+    bit_size: 3

data/registers/vrefbuf_v2b.yaml

@@ -0,0 +1,37 @@
+block/VREFBUF:
+  description: Voltage reference buffer.
+  items:
+  - name: CSR
+    description: VREF_BUF Control and Status Register.
+    byte_offset: 0
+    fieldset: CSR
+  - name: CCR
+    description: VREF_BUF Calibration Control Register.
+    byte_offset: 4
+    fieldset: CCR
+fieldset/CCR:
+  description: VREF_BUF Calibration Control Register.
+  fields:
+  - name: TRIM
+    description: Trimming code.
+    bit_offset: 0
+    bit_size: 6
+fieldset/CSR:
+  description: VREF_BUF Control and Status Register.
+  fields:
+  - name: ENVR
+    description: Enable Voltage Reference.
+    bit_offset: 0
+    bit_size: 1
+  - name: HIZ
+    description: High impedence mode for the VREF_BUF.
+    bit_offset: 1
+    bit_size: 1
+  - name: VRR
+    description: Voltage reference buffer ready.
+    bit_offset: 3
+    bit_size: 1
+  - name: VRS
+    description: Voltage reference scale.
+    bit_offset: 4
+    bit_size: 2