stm32-data/data/registers/pwr_u0.yaml

block/PWR:
  description: PWR register block
  items:
  - name: CR1
    description: Power control register 1
    byte_offset: 0
    fieldset: CR1
  - name: CR2
    description: Power control register 2
    byte_offset: 4
    fieldset: CR2
  - name: CR3
    description: Power control register 3
    byte_offset: 8
    fieldset: CR3
  - name: CR4
    description: Power control register 4
    byte_offset: 12
    fieldset: CR4
  - name: SR1
    description: Power status register 1
    byte_offset: 16
    fieldset: SR1
  - name: SR2
    description: Power status register 2
    byte_offset: 20
    fieldset: SR2
  - name: SCR
    description: Power status clear register
    byte_offset: 24
    fieldset: SCR
  - name: PUCRA
    description: Power Port A pull-up control register
    byte_offset: 32
    fieldset: PUCRA
  - name: PDCRA
    description: Power Port A pull-down control register
    byte_offset: 36
    fieldset: PDCRA
  - name: PUCRB
    description: Power Port B pull-up control register
    byte_offset: 40
    fieldset: PUCRB
  - name: PDCRB
    description: Power Port B pull-down control register
    byte_offset: 44
    fieldset: PDCRB
  - name: PUCRC
    description: Power Port C pull-up control register
    byte_offset: 48
    fieldset: PUCRC
  - name: PDCRC
    description: Power Port C pull-down control register
    byte_offset: 52
    fieldset: PDCRC
  - name: PUCRD
    description: Power Port D pull-up control register
    byte_offset: 56
    fieldset: PUCRD
  - name: PDCRD
    description: Power Port D pull-down control register
    byte_offset: 60
    fieldset: PDCRD
  - name: PUCRE
    description: Power Port E pull-up control register
    byte_offset: 64
    fieldset: PUCRE
  - name: PDCRE
    description: Power Port E pull-down control register
    byte_offset: 68
    fieldset: PDCRE
  - name: PUCRF
    description: Power Port F pull-up control register
    byte_offset: 72
    fieldset: PUCRF
  - name: PDCRF
    description: Power Port F pull-down control register
    byte_offset: 76
    fieldset: PDCRF
fieldset/CR1:
  description: Power control register 1
  fields:
  - name: LPMS
    description: 'Low-power mode selection These bits select the low-power mode entered when CPU enters the deepsleep mode. 1xx: Shutdown mode Note: If LPR bit is set, Stop 2 mode cannot be selected and Stop 1 mode shall be entered instead of Stop 2. Note: In Standby mode, SRAM2 can be preserved or not, depending on RRS bit configuration in PWR_CR3.'
    bit_offset: 0
    bit_size: 3
    enum: LPMS
  - name: FPD_STOP
    description: Flash memory powered down during Stop mode. This bit determines whether the flash memory is put in power-down mode or remains in idle mode when the device enters Stop mode.
    bit_offset: 3
    bit_size: 1
  - name: FPD_LPRUN
    description: Flash memory powered down during Low-power run mode. This bit determines whether the flash memory is put in power-down mode or remains in idle mode when the device enters Low-power sleep mode.
    bit_offset: 4
    bit_size: 1
  - name: FPD_LPSLP
    description: Flash memory powered down during Low-power sleep mode. This bit determines whether the flash memory is put in power-down mode or remains in idle mode when the device enters Low-power sleep mode.
    bit_offset: 5
    bit_size: 1
  - name: DBP
    description: Disable backup domain write protection In reset state, the RTC and backup registers are protected against parasitic write access. This bit must be set to enable write access to these registers.
    bit_offset: 8
    bit_size: 1
  - name: VOS
    description: Voltage scaling range selection
    bit_offset: 9
    bit_size: 2
    enum: VOS
  - name: LPR
    description: 'Low-power run When this bit is set, the regulator is switched from main mode (MR) to low-power mode (LPR). Note: Stop 2 mode cannot be entered when LPR bit is set. Stop 1 is entered instead.'
    bit_offset: 14
    bit_size: 1
fieldset/CR2:
  description: Power control register 2
  fields:
  - name: PVDE
    description: 'Programmable voltage detector enable Note: This bit is write-protected when the bit PVDL (PVD Lock) is set in the SYSCFG_CBR register. Note: This bit is reset only by a system reset.'
    bit_offset: 0
    bit_size: 1
  - name: PLS
    description: 'Programmable voltage detector level selection. These bits select the voltage threshold detected by the programmable voltage detector: Note: These bits are write-protected when the bit PVDL (PVD Lock) is set in the SYSCFG_CBR register. Note: These bits are reset only by a system reset.'
    bit_offset: 1
    bit_size: 3
    enum: PLS
  - name: PVME1
    description: 'Peripheral voltage monitoring 1 enable: V<sub>DDUSB</sub> vs. 1.21V'
    bit_offset: 4
    bit_size: 1
  - name: PVME3
    description: 'Peripheral voltage monitoring 3 enable: V<sub>DDA</sub> vs. 1.621V'
    bit_offset: 5
    bit_size: 1
  - name: PVME4
    description: 'Peripheral voltage monitoring 4 enable: V<sub>DDA</sub> vs. 1.861V'
    bit_offset: 6
    bit_size: 1
  - name: USV
    description: V<sub>DDUSB</sub> USB supply valid This bit is used to validate the V<sub>DDUSB</sub> supply for electrical and logical isolation purpose. Setting this bit is mandatory to use the USB FS peripheral. If V<sub>DDUSB</sub> is not always present in the application, the PVM can be used to determine whether this supply is ready or not.
    bit_offset: 10
    bit_size: 1
fieldset/CR3:
  description: Power control register 3
  fields:
  - name: EWUP1
    description: Enable Wake-up pin WKUP1 When this bit is set, the external wake-up pin WKUP1 is enabled and triggers a wake-up from Standby or Shutdown event when a rising or a falling edge occurs. The active edge is configured via the WP1 bit in the PWR_CR4 register.
    bit_offset: 0
    bit_size: 1
  - name: EWUP2
    description: Enable Wake-up pin WKUP2 When this bit is set, the external wake-up pin WKUP2 is enabled and triggers a wake-up from Standby or Shutdown event when a rising or a falling edge occurs. The active edge is configured via the WP2 bit in the PWR_CR4 register.
    bit_offset: 1
    bit_size: 1
  - name: EWUP3
    description: Enable Wake-up pin WKUP3 When this bit is set, the external wake-up pin WKUP3 is enabled and triggers a wake-up from Standby or Shutdown event when a rising or a falling edge occurs. The active edge is configured via the WP3 bit in the PWR_CR4 register.
    bit_offset: 2
    bit_size: 1
  - name: EWUP4
    description: Enable Wake-up pin WKUP4 When this bit is set, the external wake-up pin WKUP4 is enabled and triggers a wake-up from Standby or Shutdown event when a rising or a falling edge occurs. The active edge is configured via the WP4 bit in the PWR_CR4 register.
    bit_offset: 3
    bit_size: 1
  - name: EWUP5
    description: Enable Wake-up pin WKUP5 When this bit is set, the external wake-up pin WKUP5 is enabled and triggers a wake-up from Standby or Shutdown event when a rising or a falling edge occurs.The active edge is configured via the WP5 bit in the PWR_CR4 register.
    bit_offset: 4
    bit_size: 1
  - name: EWUP7
    description: Enable Wake-up pin WKUP7. When this bit is set, the external wake-up pin WKUP7 is enabled and triggers a wake-up from Standby or Shutdown event when a rising or a falling edge occurs.The active edge is configured via the WP7 bit in the PWR_CR4 register.
    bit_offset: 6
    bit_size: 1
  - name: RRS
    description: SRAM2 retention in Standby mode
    bit_offset: 8
    bit_size: 1
  - name: ENULP
    description: Enable ULP sampling When this bit is set, the BORL, BORH and PVD are periodically sampled instead continuous monitoring to reduce power consumption. Fast supply drop between two sample/compare phases is not detected in this mode. This bit has impact only on STOP2, Standby and shutdown low power modes.
    bit_offset: 9
    bit_size: 1
  - name: APC
    description: Apply pull-up and pull-down configuration When this bit is set, the I/O pull-up and pull-down configurations defined in the PWR_PUCRx and PWR_PDCRx registers are applied. When this bit is cleared, the PWR_PUCRx and PWR_PDCRx registers are not applied to the I/Os, instead the I/Os are in floating mode during Standby or configured according GPIO controller GPIOx_PUPDR register during RUN mode.
    bit_offset: 10
    bit_size: 1
  - name: EIWUL
    description: Enable internal wake-up line
    bit_offset: 15
    bit_size: 1
fieldset/CR4:
  description: Power control register 4
  fields:
  - name: WP1
    description: Wake-up pin WKUP1 polarity This bit defines the polarity used for an event detection on external wake-up pin, WKUP1
    bit_offset: 0
    bit_size: 1
  - name: WP2
    description: Wake-up pin WKUP2 polarity This bit defines the polarity used for an event detection on external wake-up pin, WKUP2
    bit_offset: 1
    bit_size: 1
  - name: WP3
    description: Wake-up pin WKUP3 polarity This bit defines the polarity used for an event detection on external wake-up pin, WKUP3
    bit_offset: 2
    bit_size: 1
  - name: WP4
    description: Wake-up pin WKUP4 polarity This bit defines the polarity used for an event detection on external wake-up pin, WKUP4
    bit_offset: 3
    bit_size: 1
  - name: WP5
    description: Wake-up pin WKUP5 polarity This bit defines the polarity used for an event detection on external wake-up pin, WKUP5
    bit_offset: 4
    bit_size: 1
  - name: WP7
    description: Wake-up pin WKUP7 polarity This bit defines the polarity used for an event detection on external wake-up pin, WKUP7
    bit_offset: 6
    bit_size: 1
  - name: VBE
    description: V<sub>BAT</sub> battery charging enable
    bit_offset: 8
    bit_size: 1
  - name: VBRS
    description: V<sub>BAT</sub> battery charging resistor selection
    bit_offset: 9
    bit_size: 1
fieldset/PDCRA:
  description: Power Port A pull-down control register
  fields:
  - name: PD0
    description: Port A pull-down bit y When set, this bit activates the pull-down on PA[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 0
    bit_size: 1
  - name: PD1
    description: Port A pull-down bit y When set, this bit activates the pull-down on PA[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 1
    bit_size: 1
  - name: PD2
    description: Port A pull-down bit y When set, this bit activates the pull-down on PA[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 2
    bit_size: 1
  - name: PD3
    description: Port A pull-down bit y When set, this bit activates the pull-down on PA[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 3
    bit_size: 1
  - name: PD4
    description: Port A pull-down bit y When set, this bit activates the pull-down on PA[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 4
    bit_size: 1
  - name: PD5
    description: Port A pull-down bit y When set, this bit activates the pull-down on PA[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 5
    bit_size: 1
  - name: PD6
    description: Port A pull-down bit y When set, this bit activates the pull-down on PA[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 6
    bit_size: 1
  - name: PD7
    description: Port A pull-down bit y When set, this bit activates the pull-down on PA[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 7
    bit_size: 1
  - name: PD8
    description: Port A pull-down bit y When set, this bit activates the pull-down on PA[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 8
    bit_size: 1
  - name: PD9
    description: Port A pull-down bit y When set, this bit activates the pull-down on PA[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 9
    bit_size: 1
  - name: PD10
    description: Port A pull-down bit y When set, this bit activates the pull-down on PA[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 10
    bit_size: 1
  - name: PD11
    description: Port A pull-down bit y When set, this bit activates the pull-down on PA[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 11
    bit_size: 1
  - name: PD12
    description: Port A pull-down bit y When set, this bit activates the pull-down on PA[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 12
    bit_size: 1
  - name: PD13
    description: Port A pull-down bit y When set, this bit activates the pull-down on PA[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 13
    bit_size: 1
  - name: PD14
    description: Port A pull-down bit y When set, this bit activates the pull-down on PA[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 14
    bit_size: 1
  - name: PD15
    description: Port A pull-down bit y When set, this bit activates the pull-down on PA[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 15
    bit_size: 1
fieldset/PDCRB:
  description: Power Port B pull-down control register
  fields:
  - name: PD0
    description: Port B pull-down bit y When set, this bit activates the pull-down on PB[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 0
    bit_size: 1
  - name: PD1
    description: Port B pull-down bit y When set, this bit activates the pull-down on PB[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 1
    bit_size: 1
  - name: PD2
    description: Port B pull-down bit y When set, this bit activates the pull-down on PB[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 2
    bit_size: 1
  - name: PD3
    description: Port B pull-down bit y When set, this bit activates the pull-down on PB[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 3
    bit_size: 1
  - name: PD4
    description: Port B pull-down bit y When set, this bit activates the pull-down on PB[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 4
    bit_size: 1
  - name: PD5
    description: Port B pull-down bit y When set, this bit activates the pull-down on PB[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 5
    bit_size: 1
  - name: PD6
    description: Port B pull-down bit y When set, this bit activates the pull-down on PB[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 6
    bit_size: 1
  - name: PD7
    description: Port B pull-down bit y When set, this bit activates the pull-down on PB[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 7
    bit_size: 1
  - name: PD8
    description: Port B pull-down bit y When set, this bit activates the pull-down on PB[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 8
    bit_size: 1
  - name: PD9
    description: Port B pull-down bit y When set, this bit activates the pull-down on PB[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 9
    bit_size: 1
  - name: PD10
    description: Port B pull-down bit y When set, this bit activates the pull-down on PB[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 10
    bit_size: 1
  - name: PD11
    description: Port B pull-down bit y When set, this bit activates the pull-down on PB[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 11
    bit_size: 1
  - name: PD12
    description: Port B pull-down bit y When set, this bit activates the pull-down on PB[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 12
    bit_size: 1
  - name: PD13
    description: Port B pull-down bit y When set, this bit activates the pull-down on PB[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 13
    bit_size: 1
  - name: PD14
    description: Port B pull-down bit y When set, this bit activates the pull-down on PB[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 14
    bit_size: 1
  - name: PD15
    description: Port B pull-down bit y When set, this bit activates the pull-down on PB[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 15
    bit_size: 1
fieldset/PDCRC:
  description: Power Port C pull-down control register
  fields:
  - name: PD0
    description: Port C pull-down bit y When set, this bit activates the pull-down on PC[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 0
    bit_size: 1
  - name: PD1
    description: Port C pull-down bit y When set, this bit activates the pull-down on PC[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 1
    bit_size: 1
  - name: PD2
    description: Port C pull-down bit y When set, this bit activates the pull-down on PC[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 2
    bit_size: 1
  - name: PD3
    description: Port C pull-down bit y When set, this bit activates the pull-down on PC[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 3
    bit_size: 1
  - name: PD4
    description: Port C pull-down bit y When set, this bit activates the pull-down on PC[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 4
    bit_size: 1
  - name: PD5
    description: Port C pull-down bit y When set, this bit activates the pull-down on PC[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 5
    bit_size: 1
  - name: PD6
    description: Port C pull-down bit y When set, this bit activates the pull-down on PC[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 6
    bit_size: 1
  - name: PD7
    description: Port C pull-down bit y When set, this bit activates the pull-down on PC[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 7
    bit_size: 1
  - name: PD8
    description: Port C pull-down bit y When set, this bit activates the pull-down on PC[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 8
    bit_size: 1
  - name: PD9
    description: Port C pull-down bit y When set, this bit activates the pull-down on PC[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 9
    bit_size: 1
  - name: PD10
    description: Port C pull-down bit y When set, this bit activates the pull-down on PC[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 10
    bit_size: 1
  - name: PD11
    description: Port C pull-down bit y When set, this bit activates the pull-down on PC[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 11
    bit_size: 1
  - name: PD12
    description: Port C pull-down bit y When set, this bit activates the pull-down on PC[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 12
    bit_size: 1
  - name: PD13
    description: Port C pull-down bit y When set, this bit activates the pull-down on PC[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 13
    bit_size: 1
  - name: PD14
    description: Port C pull-down bit y When set, this bit activates the pull-down on PC[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 14
    bit_size: 1
  - name: PD15
    description: Port C pull-down bit y When set, this bit activates the pull-down on PC[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 15
    bit_size: 1
fieldset/PDCRD:
  description: Power Port D pull-down control register
  fields:
  - name: PD0
    description: Port D pull-down bit y When set, this bit activates the pull-down on PD[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 0
    bit_size: 1
  - name: PD1
    description: Port D pull-down bit y When set, this bit activates the pull-down on PD[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 1
    bit_size: 1
  - name: PD2
    description: Port D pull-down bit y When set, this bit activates the pull-down on PD[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 2
    bit_size: 1
  - name: PD3
    description: Port D pull-down bit y When set, this bit activates the pull-down on PD[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 3
    bit_size: 1
  - name: PD4
    description: Port D pull-down bit y When set, this bit activates the pull-down on PD[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 4
    bit_size: 1
  - name: PD5
    description: Port D pull-down bit y When set, this bit activates the pull-down on PD[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 5
    bit_size: 1
  - name: PD6
    description: Port D pull-down bit y When set, this bit activates the pull-down on PD[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 6
    bit_size: 1
  - name: PD8
    description: Port D pull-down bit y When set, this bit activates the pull-down on PD[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 8
    bit_size: 1
  - name: PD9
    description: Port D pull-down bit y When set, this bit activates the pull-down on PD[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 9
    bit_size: 1
  - name: PD10
    description: Port D pull-down bit y When set, this bit activates the pull-down on PD[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 10
    bit_size: 1
  - name: PD11
    description: Port D pull-down bit y When set, this bit activates the pull-down on PD[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 11
    bit_size: 1
  - name: PD12
    description: Port D pull-down bit y When set, this bit activates the pull-down on PD[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 12
    bit_size: 1
  - name: PD13
    description: Port D pull-down bit y When set, this bit activates the pull-down on PD[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 13
    bit_size: 1
fieldset/PDCRE:
  description: Power Port E pull-down control register
  fields:
  - name: PD3
    description: Port E pull-down bit 3 When set, this bit activates the pull-down on PE[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 3
    bit_size: 1
  - name: PD7
    description: Port E pull-down bit y When set, this bit activates the pull-down on PE[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 7
    bit_size: 1
  - name: PD8
    description: Port E pull-down bit y When set, this bit activates the pull-down on PE[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 8
    bit_size: 1
  - name: PD9
    description: Port E pull-down bit y When set, this bit activates the pull-down on PE[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 9
    bit_size: 1
fieldset/PDCRF:
  description: Power Port F pull-down control register
  fields:
  - name: PD0
    description: Port F pull-down bit y When set, this bit activates the pull-down on PH[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 0
    bit_size: 1
  - name: PD1
    description: Port F pull-down bit y When set, this bit activates the pull-down on PH[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 1
    bit_size: 1
  - name: PD2
    description: Port F pull-down bit y When set, this bit activates the pull-down on PH[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 2
    bit_size: 1
  - name: PD3
    description: Port F pull-down bit y When set, this bit activates the pull-down on PH[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 3
    bit_size: 1
fieldset/PUCRA:
  description: Power Port A pull-up control register
  fields:
  - name: PU0
    description: Port A pull-up bit y (y1=115 to 0) When set, this bit activates the pull-up on PA[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 0
    bit_size: 1
  - name: PU1
    description: Port A pull-up bit y (y1=115 to 0) When set, this bit activates the pull-up on PA[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 1
    bit_size: 1
  - name: PU2
    description: Port A pull-up bit y (y1=115 to 0) When set, this bit activates the pull-up on PA[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 2
    bit_size: 1
  - name: PU3
    description: Port A pull-up bit y (y1=115 to 0) When set, this bit activates the pull-up on PA[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 3
    bit_size: 1
  - name: PU4
    description: Port A pull-up bit y (y1=115 to 0) When set, this bit activates the pull-up on PA[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 4
    bit_size: 1
  - name: PU5
    description: Port A pull-up bit y (y1=115 to 0) When set, this bit activates the pull-up on PA[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 5
    bit_size: 1
  - name: PU6
    description: Port A pull-up bit y (y1=115 to 0) When set, this bit activates the pull-up on PA[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 6
    bit_size: 1
  - name: PU7
    description: Port A pull-up bit y (y1=115 to 0) When set, this bit activates the pull-up on PA[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 7
    bit_size: 1
  - name: PU8
    description: Port A pull-up bit y (y1=115 to 0) When set, this bit activates the pull-up on PA[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 8
    bit_size: 1
  - name: PU9
    description: Port A pull-up bit y (y1=115 to 0) When set, this bit activates the pull-up on PA[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 9
    bit_size: 1
  - name: PU10
    description: Port A pull-up bit y (y1=115 to 0) When set, this bit activates the pull-up on PA[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 10
    bit_size: 1
  - name: PU11
    description: Port A pull-up bit y (y1=115 to 0) When set, this bit activates the pull-up on PA[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 11
    bit_size: 1
  - name: PU12
    description: Port A pull-up bit y (y1=115 to 0) When set, this bit activates the pull-up on PA[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 12
    bit_size: 1
  - name: PU13
    description: Port A pull-up bit y (y1=115 to 0) When set, this bit activates the pull-up on PA[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 13
    bit_size: 1
  - name: PU14
    description: Port A pull-up bit y (y1=115 to 0) When set, this bit activates the pull-up on PA[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 14
    bit_size: 1
  - name: PU15
    description: Port A pull-up bit y (y1=115 to 0) When set, this bit activates the pull-up on PA[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 15
    bit_size: 1
fieldset/PUCRB:
  description: Power Port B pull-up control register
  fields:
  - name: PU0
    description: Port B pull-up bit y When set, this bit activates the pull-up on PB[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 0
    bit_size: 1
  - name: PU1
    description: Port B pull-up bit y When set, this bit activates the pull-up on PB[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 1
    bit_size: 1
  - name: PU2
    description: Port B pull-up bit y When set, this bit activates the pull-up on PB[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 2
    bit_size: 1
  - name: PU3
    description: Port B pull-up bit y When set, this bit activates the pull-up on PB[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 3
    bit_size: 1
  - name: PU4
    description: Port B pull-up bit y When set, this bit activates the pull-up on PB[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 4
    bit_size: 1
  - name: PU5
    description: Port B pull-up bit y When set, this bit activates the pull-up on PB[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 5
    bit_size: 1
  - name: PU6
    description: Port B pull-up bit y When set, this bit activates the pull-up on PB[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 6
    bit_size: 1
  - name: PU7
    description: Port B pull-up bit y When set, this bit activates the pull-up on PB[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 7
    bit_size: 1
  - name: PU8
    description: Port B pull-up bit y When set, this bit activates the pull-up on PB[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 8
    bit_size: 1
  - name: PU9
    description: Port B pull-up bit y When set, this bit activates the pull-up on PB[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 9
    bit_size: 1
  - name: PU10
    description: Port B pull-up bit y When set, this bit activates the pull-up on PB[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 10
    bit_size: 1
  - name: PU11
    description: Port B pull-up bit y When set, this bit activates the pull-up on PB[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 11
    bit_size: 1
  - name: PU12
    description: Port B pull-up bit y When set, this bit activates the pull-up on PB[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 12
    bit_size: 1
  - name: PU13
    description: Port B pull-up bit y When set, this bit activates the pull-up on PB[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 13
    bit_size: 1
  - name: PU14
    description: Port B pull-up bit y When set, this bit activates the pull-up on PB[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 14
    bit_size: 1
  - name: PU15
    description: Port B pull-up bit y When set, this bit activates the pull-up on PB[y] when APC bit is set in PWR_CR3 register.
    bit_offset: 15
    bit_size: 1
fieldset/PUCRC:
  description: Power Port C pull-up control register
  fields:
  - name: PU0
    description: Port C pull-up bit y When set, this bit activates the pull-up on PC[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 0
    bit_size: 1
  - name: PU1
    description: Port C pull-up bit y When set, this bit activates the pull-up on PC[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 1
    bit_size: 1
  - name: PU2
    description: Port C pull-up bit y When set, this bit activates the pull-up on PC[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 2
    bit_size: 1
  - name: PU3
    description: Port C pull-up bit y When set, this bit activates the pull-up on PC[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 3
    bit_size: 1
  - name: PU4
    description: Port C pull-up bit y When set, this bit activates the pull-up on PC[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 4
    bit_size: 1
  - name: PU5
    description: Port C pull-up bit y When set, this bit activates the pull-up on PC[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 5
    bit_size: 1
  - name: PU6
    description: Port C pull-up bit y When set, this bit activates the pull-up on PC[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 6
    bit_size: 1
  - name: PU7
    description: Port C pull-up bit y When set, this bit activates the pull-up on PC[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 7
    bit_size: 1
  - name: PU8
    description: Port C pull-up bit y When set, this bit activates the pull-up on PC[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 8
    bit_size: 1
  - name: PU9
    description: Port C pull-up bit y When set, this bit activates the pull-up on PC[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 9
    bit_size: 1
  - name: PU10
    description: Port C pull-up bit y When set, this bit activates the pull-up on PC[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 10
    bit_size: 1
  - name: PU11
    description: Port C pull-up bit y When set, this bit activates the pull-up on PC[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 11
    bit_size: 1
  - name: PU12
    description: Port C pull-up bit y When set, this bit activates the pull-up on PC[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 12
    bit_size: 1
  - name: PU13
    description: Port C pull-up bit y When set, this bit activates the pull-up on PC[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 13
    bit_size: 1
  - name: PU14
    description: Port C pull-up bit y When set, this bit activates the pull-up on PC[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 14
    bit_size: 1
  - name: PU15
    description: Port C pull-up bit y When set, this bit activates the pull-up on PC[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 15
    bit_size: 1
fieldset/PUCRD:
  description: Power Port D pull-up control register
  fields:
  - name: PU0
    description: Port D pull-up bit y When set, this bit activates the pull-up on PD[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 0
    bit_size: 1
  - name: PU1
    description: Port D pull-up bit y When set, this bit activates the pull-up on PD[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 1
    bit_size: 1
  - name: PU2
    description: Port D pull-up bit y When set, this bit activates the pull-up on PD[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 2
    bit_size: 1
  - name: PU3
    description: Port D pull-up bit y When set, this bit activates the pull-up on PD[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 3
    bit_size: 1
  - name: PU4
    description: Port D pull-up bit y When set, this bit activates the pull-up on PD[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 4
    bit_size: 1
  - name: PU5
    description: Port D pull-up bit y When set, this bit activates the pull-up on PD[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 5
    bit_size: 1
  - name: PU6
    description: Port D pull-up bit y When set, this bit activates the pull-up on PD[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 6
    bit_size: 1
  - name: PU8
    description: Port D pull-up bit y When set, this bit activates the pull-up on PD[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 8
    bit_size: 1
  - name: PU9
    description: Port D pull-up bit y When set, this bit activates the pull-up on PD[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 9
    bit_size: 1
  - name: PU10
    description: Port D pull-up bit y When set, this bit activates the pull-up on PD[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 10
    bit_size: 1
  - name: PU11
    description: Port D pull-up bit y When set, this bit activates the pull-up on PD[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 11
    bit_size: 1
  - name: PU12
    description: Port D pull-up bit y When set, this bit activates the pull-up on PD[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 12
    bit_size: 1
  - name: PU13
    description: Port D pull-up bit y When set, this bit activates the pull-up on PD[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 13
    bit_size: 1
fieldset/PUCRE:
  description: Power Port E pull-up control register
  fields:
  - name: PU3
    description: Port E pull-up bit 3 When set, this bit activates the pull-up on PE[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 3
    bit_size: 1
  - name: PU7
    description: Port E pull-up bit y When set, this bit activates the pull-up on PE[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 7
    bit_size: 1
  - name: PU8
    description: Port E pull-up bit y When set, this bit activates the pull-up on PE[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 8
    bit_size: 1
  - name: PU9
    description: Port E pull-up bit y When set, this bit activates the pull-up on PE[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 9
    bit_size: 1
fieldset/PUCRF:
  description: Power Port F pull-up control register
  fields:
  - name: PU0
    description: Port F pull-up bit y When set, this bit activates the pull-up on PH[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 0
    bit_size: 1
  - name: PU1
    description: Port F pull-up bit y When set, this bit activates the pull-up on PH[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 1
    bit_size: 1
  - name: PU2
    description: Port F pull-up bit y When set, this bit activates the pull-up on PH[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 2
    bit_size: 1
  - name: PU3
    description: Port F pull-up bit y When set, this bit activates the pull-up on PH[y] when APC bit is set in PWR_CR3 register. If the corresponding PDy bit is also set, the pull-up is not activated and the pull-down is activated instead with highest priority.
    bit_offset: 3
    bit_size: 1
fieldset/SCR:
  description: Power status clear register
  fields:
  - name: CWUF1
    description: Clear wake-up flag 1 Setting this bit clears the WUF1 flag in the PWR_SR1 register.
    bit_offset: 0
    bit_size: 1
  - name: CWUF2
    description: Clear wake-up flag 2 Setting this bit clears the WUF2 flag in the PWR_SR1 register.
    bit_offset: 1
    bit_size: 1
  - name: CWUF3
    description: Clear wake-up flag 3 Setting this bit clears the WUF3 flag in the PWR_SR1 register.
    bit_offset: 2
    bit_size: 1
  - name: CWUF4
    description: Clear wake-up flag 4 Setting this bit clears the WUF4 flag in the PWR_SR1 register.
    bit_offset: 3
    bit_size: 1
  - name: CWUF5
    description: Clear wake-up flag 5 Setting this bit clears the WUF5 flag in the PWR_SR1 register.
    bit_offset: 4
    bit_size: 1
  - name: CWUF7
    description: Clear wake-up flag 7 Setting this bit clears the WUF7 flag in the PWR_SR1 register.
    bit_offset: 6
    bit_size: 1
  - name: CSBF
    description: Clear standby flag Setting this bit clears the SBF flag in the PWR_SR1 register.
    bit_offset: 8
    bit_size: 1
fieldset/SR1:
  description: Power status register 1
  fields:
  - name: WUF1
    description: Wake-up flag 1 This bit is set when a wake-up event is detected on wake-up pin, WKUP1. It is cleared by writing 1 in the CWUF1 bit of the PWR_SCR register.
    bit_offset: 0
    bit_size: 1
  - name: WUF2
    description: Wake-up flag 2 This bit is set when a wake-up event is detected on wake-up pin, WKUP2. It is cleared by writing 1 in the CWUF2 bit of the PWR_SCR register.
    bit_offset: 1
    bit_size: 1
  - name: WUF3
    description: Wake-up flag 3 This bit is set when a wake-up event is detected on wake-up pin, WKUP3. It is cleared by writing 1 in the CWUF3 bit of the PWR_SCR register.
    bit_offset: 2
    bit_size: 1
  - name: WUF4
    description: Wake-up flag 4 This bit is set when a wake-up event is detected on wake-up pin,WKUP4. It is cleared by writing 1 in the CWUF4 bit of the PWR_SCR register.
    bit_offset: 3
    bit_size: 1
  - name: WUF5
    description: Wake-up flag 5 This bit is set when a wake-up event is detected on wake-up pin, WKUP5. It is cleared by writing 1 in the CWUF5 bit of the PWR_SCR register.
    bit_offset: 4
    bit_size: 1
  - name: WUF7
    description: Wake-up flag 7 This bit is set when a wake-up event is detected on wake-up pin, WKUP7. It is cleared by writing 1 in the CWUF7 bit of the PWR_SCR register.
    bit_offset: 6
    bit_size: 1
  - name: SBF
    description: Standby flag This bit is set by hardware when the device enters the Standby mode and is cleared by setting the CSBF bit in the PWR_SCR register, or by a power-on reset. It is not cleared by the system reset.
    bit_offset: 8
    bit_size: 1
  - name: STOPF
    description: Stop Flags These bits are set by hardware when the device enters any stop mode and are cleared by setting the CSBF bit in the PWR_SCR register, or by a power-on reset. It is not cleared by the system reset.
    bit_offset: 9
    bit_size: 3
    enum: STOPF
  - name: WUFI
    description: Wake-up flag internal This bit is set when a wake-up is detected on the internal wake-up line. It is cleared when all internal wake-up sources are cleared.
    bit_offset: 15
    bit_size: 1
fieldset/SR2:
  description: Power status register 2
  fields:
  - name: FLASH_RDY
    description: 'Flash ready flag This bit is set by hardware to indicate when the flash memory is readey to be accessed after wake-up from power-down. To place the flash memory in power-down, set either FPD_LPRUN, FPD_LPSLP or FPD_STP bits. Note : If the system boots from SRAM, the user application must wait until the FLASH_RDY bit is set, prior to jumping to flash memory.'
    bit_offset: 7
    bit_size: 1
  - name: REGLPS
    description: Low-power regulator started This bit provides the information whether the low-power regulator is ready after a power-on reset or a Standby/Shutdown. If the Standby mode is entered while REGLPS bit is still cleared, the wake-up from Standby mode time may be increased.
    bit_offset: 8
    bit_size: 1
  - name: REGLPF
    description: Low-power regulator flag This bit is set by hardware when the MCU is in Low-power run mode. When the MCU exits from the Low-power run mode, this bit remains at 1 until the regulator is ready in main mode. A polling on this bit must be done before increasing the product frequency. This bit is cleared by hardware when the regulator is ready.
    bit_offset: 9
    bit_size: 1
  - name: VOSF
    description: Voltage scaling flag A delay is required for the internal regulator to be ready after the voltage scaling has been changed. VOSF indicates that the regulator reached the voltage level defined with VOS bits of the PWR_CR1 register.
    bit_offset: 10
    bit_size: 1
  - name: PVDO
    description: Programmable voltage detector output
    bit_offset: 11
    bit_size: 1
  - name: PVMO1
    description: 'Peripheral voltage monitoring output: V<sub>DDUSB</sub> vs. 1.2 V Note: PVMO1 is cleared when PVM1 is disabled (PVME1 = 0). After enabling PVM1, the PVM1 output is valid after the PVM1 wake-up time.'
    bit_offset: 12
    bit_size: 1
  - name: PVMO3
    description: 'Peripheral voltage monitoring output: V<sub>DDA</sub> vs. 1.621V Note: PVMO3 is cleared when PVM3 is disabled (PVME3 = 0). After enabling PVM3, the PVM3 output is valid after the PVM3 wake-up time.'
    bit_offset: 14
    bit_size: 1
  - name: PVMO4
    description: 'Peripheral voltage monitoring output: V<sub>DDA</sub> vs. 2.21V Note: PVMO4 is cleared when PVM4 is disabled (PVME4 = 0). After enabling PVM4, the PVM4 output is valid after the PVM4 wake-up time.'
    bit_offset: 15
    bit_size: 1
enum/LPMS:
  bit_size: 3
  variants:
  - name: Stop0
    description: Stop 0 mode
    value: 0
  - name: Stop1
    description: Stop 1 mode
    value: 1
  - name: Stop2
    description: Stop 2 mode
    value: 2
  - name: Standby
    description: Standby mode
    value: 3
enum/PLS:
  bit_size: 3
  variants:
  - name: B_0x0
    description: V<sub>PVD0</sub> around 2.01V
    value: 0
  - name: B_0x1
    description: V<sub>PVD1</sub> around 2.21V
    value: 1
  - name: B_0x2
    description: V<sub>PVD2</sub> around 2.41V
    value: 2
  - name: B_0x3
    description: V<sub>PVD3</sub> around 2.51V
    value: 3
  - name: B_0x4
    description: V<sub>PVD4</sub> around 2.61V
    value: 4
  - name: B_0x5
    description: V<sub>PVD5</sub> around 2.81V
    value: 5
  - name: B_0x6
    description: V<sub>PVD6</sub> around 2.91V
    value: 6
  - name: B_0x7
    description: External input analog voltage PVD_IN (compared internally to VREFINT)
    value: 7
enum/STOPF:
  bit_size: 3
  variants:
  - name: None
    description: The device did not enter any Stop mode.
    value: 0
  - name: Stop0
    description: The device entered in Stop 0 mode.
    value: 4
  - name: Stop1
    description: The device entered in Stop 1 mode.
    value: 5
  - name: Stop2
    description: The device entered in Stop 2 mode.
    value: 6
enum/VOS:
  bit_size: 2
  variants:
  - name: Range1
    description: Range 1
    value: 1
  - name: Range2
    description: Range 2
    value: 2