stm32-data/data/registers/pwr_c0.yaml

---
block/PWR:
  description: PWR address block description
  items:
    - name: CR1
      description: PWR control register 1
      byte_offset: 0
      fieldset: CR1
    - name: CR3
      description: PWR control register 3
      byte_offset: 8
      fieldset: CR3
    - name: CR4
      description: PWR control register 4
      byte_offset: 12
      fieldset: CR4
    - name: SR1
      description: PWR status register 1
      byte_offset: 16
      fieldset: SR1
    - name: SR2
      description: PWR status register 2
      byte_offset: 20
      fieldset: SR2
    - name: SCR
      description: PWR status clear register
      byte_offset: 24
      fieldset: SCR
    - name: PUCR
      description: PWR Port pull-up control register
      array:
        len: 6
        stride: 8
      byte_offset: 32
      fieldset: PCR
    - name: PDCR
      description: PWR Port pull-down control register
      array:
        len: 6
        stride: 8
      byte_offset: 36
      fieldset: PCR
fieldset/CR1:
  description: PWR control register 1
  fields:
    - name: LPMS
      description: "Low-power mode selection\r These bits select the low-power mode entered when CPU enters deepsleep mode.\r 1XX: Shutdown mode"
      bit_offset: 0
      bit_size: 3
    - name: FPD_STOP
      description: "Flash memory powered down during Stop mode\r This bit determines whether the Flash memory is put in power-down mode or remains in idle mode when the device enters Stop mode."
      bit_offset: 3
      bit_size: 1
    - name: FPD_SLP
      description: "Flash memory powered down during Sleep mode\r This bit determines whether the Flash memory is put in power-down mode or remains in idle mode when the device enters Sleep mode."
      bit_offset: 5
      bit_size: 1
fieldset/CR3:
  description: PWR control register 3
  fields:
    - name: EWUP
      description: Enable Wakeup pin
      bit_offset: 0
      bit_size: 1
      array:
        len: 6
        stride: 1
    - name: APC
      description: "Apply pull-up and pull-down configuration\r This bit determines whether the I/O pull-up and pull-down configurations defined in the PWR_PUCRx and PWR_PDCRx registers are applied."
      bit_offset: 10
      bit_size: 1
    - name: EIWUL
      description: "Enable internal wakeup line\r When set, a rising edge on the internal wakeup line triggers a wakeup event."
      bit_offset: 15
      bit_size: 1
fieldset/CR4:
  description: PWR control register 4
  fields:
    - name: WP
      description: Wakeup pin WKUP1 polarity
      bit_offset: 0
      bit_size: 1
      array:
        len: 6
        stride: 1
fieldset/PCR:
  description: Power Port pull control register
  fields:
    - name: P
      description: Port pull bit y (y=0..15)
      bit_offset: 0
      bit_size: 1
      array:
        len: 16
        stride: 1
fieldset/SCR:
  description: PWR status clear register
  fields:
    - name: CWUF
      description: Clear Wakeup flag
      bit_offset: 0
      bit_size: 1
      array:
        len: 6
        stride: 1
    - name: CSBF
      description: "Clear standby flag\r Setting this bit clears the SBF flag in the PWR_SR1 register."
      bit_offset: 8
      bit_size: 1
fieldset/SR1:
  description: PWR status register 1
  fields:
    - name: WUF
      description: Wakeup flag
      bit_offset: 0
      bit_size: 1
      array:
        len: 6
        stride: 1
    - name: SBF
      description: "Standby/Shutdown flag\r This bit is set by hardware when the device enters Standby or Shutdown mode and is cleared by setting the CSBF bit in the PWR_SCR register, or by a power-on reset. It is not cleared by the system reset."
      bit_offset: 8
      bit_size: 1
    - name: WUFI
      description: "Wakeup flag internal\r This bit is set when a wakeup condition is detected on the internal wakeup line. It is cleared when all internal wakeup sources are cleared."
      bit_offset: 15
      bit_size: 1
fieldset/SR2:
  description: PWR status register 2
  fields:
    - name: FLASH_RDY
      description: "Flash ready flag\r This bit is set by hardware to indicate when the Flash memory is ready to be accessed after wakeup from power-down. To place the Flash memory in power-down, set either FPD_SLP or FPD_STP bit.\r Note: If the system boots from SRAM, the user application must wait till FLASH_RDY bit is set, prior to jumping to Flash memory."
      bit_offset: 7
      bit_size: 1